The parts that
keep it working.
The consumable side of containment is unglamorous and it is where compliance quietly erodes. When the mounting strips run out, someone reaches for duct tape. When the fasteners fail, a panel corner comes loose and the containment starts leaking at exactly the place nobody is looking. Keeping fasteners, refills, and accessories in stock is a small line item that protects everything else on the project.
The full Fasteners & Accessories catalog.
Oncore VettedRE-U-ZIP® Hook & Loop Faster Strips
Reusable hook-and-loop fastener strips for rapid attachment, removal, and reinstallation of dust barrier zippers and panels.
Oncore VettedRE-U-ZIP® HOOK & LOOP FASTENER TABS
Reusable hook-and-loop fastener tabs for spot-attachment of dust barrier zippers and panels in tight or irregular spaces.
Oncore VettedRE-U-ZIP® Mounting Strip Re-Fill™ | 12-Pack
Replacement adhesive Mounting Strip Re-Fills™ — peel-and-stick the reusable side of RE-U-ZIP's hook-and-loop containment system.
Oncore VettedRE-U-ZIP® Mounting Strip Re-Fill™ | 180 Unit Case Pack
Bulk case-pack of Mounting Strip Re-Fills™ for high-volume contractors and healthcare facility teams.
Oncore VettedRE-U-ZIP® Mounting Strip Re-FIll™ | 3-PACK
3-pack of Mounting Strip Re-Fills™ — keep a small reserve on hand for quick barrier reconfiguration.
Oncore VettedRE-U-ZIP® DUST BARRIER ZIPPER CABLE LOCK
Lockable cable accessory for RE-U-ZIP zippered dust barriers — reduces job-site liability and tampering at the entry point.
Oncore VettedRE-U-ZIP® DUST BARRIER ZIPPER CARRY BAG
Heavy-duty carry bag to keep RE-U-ZIP zippers and Magnetic Entry Strips organized between job sites.
Oncore VettedRE-U-ZIP® SURFACE PROTECTION TAPE
Premium surface protection tape engineered to pair with RE-U-ZIP barriers without leaving residue on finished hospital surfaces.
Oncore VettedRE-U-ZIP® Magnetic Extensions™
Magnetic Extension pieces for taller dust barriers and non-standard openings using the RE-U-ZIP Magnetic Entry Strip™ system.
Oncore VettedRE-U-ZIP® DUST BARRIER ZIPPER CARRY CASE
Heavy-duty carry case to keep RE-U-ZIP zippers and Magnetic Entry Strips organized between job sites.
What to check before you buy.
Guidance from the Oncore consultants who write these permits and inspect the barriers that come out of them.
Ask a Consultant- 01
Order refills on the same cycle as the work, not when they run out. The adhesive mounting components are consumed fastest, and a stockout is what drives crews to improvise a seal.
- 02
Standardize the attachment system across the facility. Mixing incompatible fastener systems between phases means the reusable components stop being reusable, which erases the reason they were specified.
- 03
Keep fastener tabs for irregular conditions. Corridors, curved walls, and casework rarely accept a continuous strip cleanly, and spot attachment is what closes those gaps properly.
- 04
Inspect attachment points, not just panels, during barrier rounds. A barrier that is intact in the middle and lifting at the edges reads as compliant from ten feet away and is not.
The classes this category serves.
Class I
Inspection and non-invasive work. Ceiling tile removal for visual inspection, painting without sanding, minor electrical or trim work.
Minimal dust is expected, so the emphasis is on immediate cleanup and keeping ceiling tiles out of the space any longer than the task requires. Most Class I work needs no barrier at all.
Class II
Small-scale, short-duration work that creates minimal dust. Cutting access panels, accessing chase spaces, sanding or patching a small wall area.
Dust control measures, HEPA vacuuming as the work proceeds, sealing unused doors and air vents, and containing debris before it leaves the space. Soft containment and entry control are usually enough.
Class III
Work that generates moderate to high dust levels, or that requires removing a fixed building component such as a wall, ductwork, or casework.
Critical barriers that fully seal the work area, negative air pressure maintained with HEPA filtration, and every penetration sealed. Pressure has to be verified, not assumed.
Not sure which class your project falls under? Oncore performs the risk assessment and writes the ICRA permit, and our ICRA 2.0 training teaches your team to do it in house.
Need the containment
scoped properly?
Buying the right product is the last step. Oncore performs the risk assessment, writes the ICRA permit, and monitors the barrier through the life of the project.